How To Repair Glass Window Pane

The trickiest office of replacing broken glass panes in wood-frame windows is getting replacement drinking glass that'south sized exactly right. To replace a cleaved drinking glass pane in a wood window, y'all need to mensurate the precise length and width of the grooves in which the pane will fit.

Have the new glass cutting and then information technology measures 1/8 inch shorter than the verbal groove dimensions in both the length and width. This creates a i/16-inch gap on each side between the edges of the pane and the rabbet groove. The gap provides room for the drinking glass to expand when the weather condition changes.

In add-on to the replacement drinking glass pane, y'all'll need: latex glazing putty; metallic glazing points; pliers; a heat gun; flexible putty knife; 1- or 2-inch, stiff, steel, putty knife; and a flathead screwdriver.

Also check out these other manufactures on replacing broken window panes in: steel-casement windows; sliding-sash windows; and metallic storm windows.

Utilise the pliers to remove all of the glass shards.

When yous piece of work with broken glass, wear rubber goggles likewise equally gloves; minor chips of glass can crusade permanent center damage.

Utilise the heat gun to warm the old putty; and and then scrape it away with a putty knife.

If the putty doesn't lift off hands, apply more than oestrus and try again. Be patient — the putty around actually old windows is as hard as concrete, but information technology volition soften.

Don't chisel out the old putty — y'all might wreck the window. The putty volition soften with enough heat and time.

Use a putty knife or the tip of a screwdriver to remove the old glazing points.

The points will be buried under the old putty.

Clean and inspect the rabbet groove.

Ensure that no glazing putty, glass shards, or glazing points remain.

Apply a dewdrop of putty on the glass side of the rabbet groove.

Clasp out a i⁄sixteen-inch bead of putty between the edge of the drinking glass and the window frame.

Gently printing downwards the glass at the edges to embed the glass into the putty.

Allow the putty to spread out and form a wet seal on the inside of the window between the glass and sash.

Position the new pane in the rabbets.

Shift the pane until you take a 1/sixteen-inch gap between the pane and sash on all iv sides.

Identify at least two new glazing points in each section of the window sash surrounding the new glass.

Infinite the points evenly effectually the perimeter, about six inches autonomously.

Use the flat side of a putty knife to button one corner of each triangular glazing point into the wood sash.

Y'all tin can use a screwdriver blade instead of a putty knife.

Grade a i/ii-inch-thick rope of putty and printing the length along all four sides of the glass.

Roll a glob of putty between your bare hands to grade the rope.

Smoothen the glazing putty and scrape away the excess.

Hold the putty knife at a 45-degree bending, press, and smooth the glazing putty against the glass and sash.

After the putty dries completely, repaint the putty and repaired area.

Don't mask off the glass before repainting. The paint volition help form a wet seal between the glass pane and the sash. Then, allow the paint to overlap about 1/8 inch onto the glass.

Almost This Article

This commodity is from the volume:

• Woodworking For Dummies ,

Nearly the book author:

Jeff Potent is a renaissance man with experience in the fields of percussion, woodworking, recording, and neuro-developmental disabilities. He is the director of the Stiff Institute—an auditory brain stimulation research organization—and creator of Brain Shift Radio, an interactive brain stimulation music site. He has been a drummer for over 40 years and has released dozens of CDs.

This commodity can be plant in the category:

• Windows ,

Source: https://www.dummies.com/article/home-auto-hobbies/home-improvement-appliances/windows-home-improvement-appliances/how-to-replace-a-broken-glass-pane-in-a-wood-frame-window-206792/

Posted by: taylorshantoote1978.blogspot.com

Share this post